Search found 24 matches

by PeteS
Thu Aug 08, 2019 12:54 pm
Forum: General Technical Discussion
Topic: Cologne rocker covers
Replies: 2
Views: 285

Cologne rocker covers

I am renovating my cologne rocker covers....it's many years since I have replaced cork gaskets ....any tips or recommendations regarding any sealants to use or are they best fitted without?
Thanks
Pete
by PeteS
Tue Jul 16, 2019 5:05 pm
Forum: Se6/6a/6b/GTC
Topic: Now what have I done!
Replies: 17
Views: 911

Now what have I done!

Thanks Phil
by PeteS
Tue Jul 16, 2019 4:36 pm
Forum: Se6/6a/6b/GTC
Topic: Now what have I done!
Replies: 17
Views: 911

Now what have I done!

Thanks Roger....if it has a Eureka wire where is it and do they fail?
by PeteS
Tue Jul 16, 2019 4:06 pm
Forum: Se6/6a/6b/GTC
Topic: Now what have I done!
Replies: 17
Views: 911

Now what have I done!

Thanks Jim just tried it again and the ignition light came on turned over and fired and died ...next try no ignition light. I'm thinking it's probably the ignition switch....have looked for the ballast but can't find it ...the coil is not exactly easy to get to even by Scimitar standards!
by PeteS
Tue Jul 16, 2019 2:50 pm
Forum: Se6/6a/6b/GTC
Topic: Now what have I done!
Replies: 17
Views: 911

Now what have I done!

Thanks Jim. For some reason I have no ignition light again. This is on a Gtc , don't know if that makes any difference? Checked that the black /white and yellow white are on the coil terminals ok. The car still turns over and fires but will not run.... weather is too hot to think straight perhaps I ...
by PeteS
Tue Jul 16, 2019 1:20 pm
Forum: Se6/6a/6b/GTC
Topic: Now what have I done!
Replies: 17
Views: 911

Now what have I done!

Thanks Jim ...so my theory of a missing White/red isn't right...any thoughts of what I can try next?
by PeteS
Tue Jul 16, 2019 1:00 pm
Forum: Se6/6a/6b/GTC
Topic: Now what have I done!
Replies: 17
Views: 911

Now what have I done!

Looking at the wiring diagram it looks as though the white/ red wire is the one that is missing......the PO had bypassed the auto inhibit switch with a feed from the connector block (by the wiper motor) to the starter solenoid
by PeteS
Tue Jul 16, 2019 12:40 pm
Forum: Se6/6a/6b/GTC
Topic: Now what have I done!
Replies: 17
Views: 911

Now what have I done!

Yes that is what's happening ...my first instinct is it something I've done
by PeteS
Tue Jul 16, 2019 12:24 pm
Forum: Se6/6a/6b/GTC
Topic: Now what have I done!
Replies: 17
Views: 911

Now what have I done!

Should read fires up and dies...predictive text !!!!!!!!!

Fixed - edit button top right :wink:
by PeteS
Tue Jul 16, 2019 12:19 pm
Forum: Se6/6a/6b/GTC
Topic: Now what have I done!
Replies: 17
Views: 911

Now what have I done!

Yesterday I replaced the wires that leave the loom and connect to the starter solenoid as the originals insulation had become brittle and cracked and the ignition light was not coming on.....thought all was well as after wards ignition light came on ok.....today I thought I would make sure it runs o...
by PeteS
Mon Jul 15, 2019 1:11 pm
Forum: General Technical Discussion
Topic: Am I inhibited ?
Replies: 20
Views: 1613

Am I inhibited ?

I found it was best to remove the plug on the inhibit switch from under the car it's a bit of a fiddle. Then the inhibit switch can be removed using a long reach six sided socket on a very long extension. From pax side of engine bay it can be seen rear of the bell housing. I have also replaced the w...
by PeteS
Fri Jul 05, 2019 9:25 am
Forum: General Technical Discussion
Topic: Am I inhibited ?
Replies: 20
Views: 1613

Am I inhibited ?

When I bought my Gtc the starter inhibit switch was bypassed. The switch tested ok for continuity between the centre pin and the first pin (reversing lights) the third pin gear lever position inhibit should have continuity with the body of the switch when the plunger is depressed. On the Gtc the inh...
by PeteS
Mon Jun 24, 2019 9:54 am
Forum: Wanted
Topic: Auto. Inhibit switch
Replies: 0
Views: 604

Auto. Inhibit switch

Hi all
I am after a C3 auto gearbox starter inhibit switch. I have removed the old switch and it's only working on the reversing light pin.
Thought I'd see if anyone has one kicking around they would sell before I order a new one.
Thanks
Pete
by PeteS
Thu Feb 14, 2019 12:13 pm
Forum: General Technical Discussion
Topic: Auto gear shifter seal
Replies: 0
Views: 590

Auto gear shifter seal

Hi all
The rubber seal either side of the auto gear( C3) selector.has become brittle over time .
Can this be replaced or repaired?
by PeteS
Tue Nov 06, 2018 2:29 pm
Forum: Removed For Sale and Ebay
Topic: GTC seat hinge cover
Replies: 0
Views: 754

GTC seat hinge cover

Gtc driver's seat recline hinge cover in black please

Go to advanced search