Fitting sliding rear brake slave cylinders

Have you documented a Scimitar related procedure and would like to share it with others? Pictures are most welcome!
Threads will be locked once posted, so any further questions in the specific forum, please.

Moderators: scimjim, philhoward, erikscimitardemon, Roger Pennington, Lukeyboy46

Post Reply
User avatar
scimjim
RSSOC Member
Posts: 35056
Joined: Sun Oct 01, 2006 10:08 pm
Location: Gloucester
Has thanked: 112 times
Been thanked: 770 times

Fitting sliding rear brake slave cylinders

Post by scimjim » Fri May 25, 2018 4:51 pm

philhoward wrote:If anyone has a foolproof and quick way of fitting the cylinder and clips, I'm all ears. Now done, but not a job I'd like to repeat in a hurry!
toomanysabres wrote:
Wed Jul 10, 2013 11:38 am
After consulting oracles far and wide (well at least the other side of the Dartford tunnel) I have the foolproof way and you will wonder what all the fuss was about.
Its the answer to life, the universe and everything about fixing the rear cylinders.

Refer to the diagram in either book its the same drawing (mine is the RSSOC Autobooks fig 11:3 p 110)
Assemble in the following order.
1) Insert cylinder 6 on its own into the backplate.
2) Slide on U clip 13 direction as shown in the manual.
3) Slide on U clip 11 BUT IN THE OPPOSITE DIRECTION TO THE MANUAL (ie same as 13) with the curved side towards the backplate.
The cylinder is now a sloppy fit in the backplate.
4) Insert handbrake lever 9 there will be enough clearance to fiddle it into place in its pocket and trapped between cylinder and backplate.
5) Insert flat clip 12 between 11 & 13 ALSO IN THE OPPOSITE DIRECTION TO THE MANUAL and get the notches locked into the tips of the adjacent clip.
6) Fit the rubber boot 10 ensuring a snug fit of the thin sides around the clip.
7) Go and have a cup of tea/beer. Simples innit.
E7F7213C-3D78-4178-92AD-56F8714ADBB3.jpeg
E7F7213C-3D78-4178-92AD-56F8714ADBB3.jpeg (164.58 KiB) Viewed 317 times
philhoward wrote:
Wed Jul 10, 2013 11:42 am
Easy when you know how...

I fitted the "matching pair" of clips with the double notches first, then the handbrake lever, then the outer clip. Second one went on much easier and quicker than the first! Left the boot off the second one first of all. Nothing a knife and superglue couldn't fix though.

Also found it much easier to fit the pipes first, then clip it to the backplate...
toomanysabres wrote:
Wed Jul 10, 2013 11:54 am
I guess previous gorillas have over bent clip 13. While its in the sloppy fit position, agreed, slip the boot on and start the unions into their threads. When clipped in check it slides up & down the slot ok and tighten the unions
philhoward wrote:
Wed Jul 10, 2013 12:10 pm
New clip kit from GW...gorilla fitting it though ;)

Edit:- Original part number if you can find a 'NOS' is Girling SP2862


Jim King

Current: SE5 (8Ball), TI SS1 (snotty), 1600 SS1 (G97), 1600 SS1 (C686CCR), 2.5TD SE5a (diesel 5a), 6 x random other SS1s.
Previous: SE5, 3 x SE5a, 2 x SE6a, 3 x SE6b, GTC, 2.9i GTC, 3 x 1600 SS1, 1300 SS1, Mk1 Ti Sabre, Mk1.5 CVH Sabre
Chief mechanic for: 1400 K series SS1 (Megan3), 1400 CVH EFi SS1 (Grawpy), Sabre/MX5 auto (The Flying Broomstick),
1300 SS1 (Number One) & Sarah's coupe.
CURE THE FAULT - NOT THE SYMPTOMS

Post Reply

Return to “How To Guides”